FN3007 

THE MANEUVERABILITY | Short wheelbase + powerful + economical

THE HAMMERMILL

Newly developed hammer mechanism for even more economical work.

The grain feed is automatic or adjustable via the feed metering.

The even coating of the mill results in a uniform grist structure and reduced grist heating.

Grinding capacities of up to 36 t / h are practical values.

THE CRUSH

Crushing performance up to 18 t / h.

The special hard material rollers are highly wear-resistant, insensitive to foreign bodies and can be reground.

Great intake performance thanks to the special grinding of the rollers, which means that even moist maize can be processed without problems.

A clearly defined squeezing gap results in a uniform structure of the squeezed product.

The tried and tested stepless gap adjustment can be adjusted centrally, optionally hydraulically from the control station.

Mixed operation (simultaneous grinding and squeezing) is possible as always.

THE TUBE BOX

Tube box (tubes made of stainless steel / housing made of aluminum) for clean storage of your suction and pressure hoses, offers space for 48m and this with a low, accessible insertion height.

THE SNAIL EMPTYING

Up to 60 t / h.

Emptying heights of up to 9125 mm are possible.

THE VARIANTS

Trunk extensions

THE VARIANTS

Storage space

THE VARIANTS

Cladding of the shelf on the right

THE MIXER

Variable mixer sizes up to 6t content = one principle!

Reasonable installation height: e.g. 5t mixer with an installation height of 2600 mm.

6t mixer with an installation height of 2900 mm.

Residual emptying through the inclined spout.

Proven for decades.

Steep mixer cone.

Large size mixer screw.

Infinitely variable speed adjustment of the mixer screw = gentle treatment of the crushed goods.

FLOW SCALE

Permanent weight recording during suction.

Simultaneous suction, weighing and emptying is guaranteed = no adversarial process = your time savings.

Maintenance and dust-free.

THE CONTROL PANEL

Everything at a glance for electrics, hydraulics and pneumatics.

Dust and weather protected.

Machine control and recipe management.

Mixing speed regulation.

Mill regulation for optimal utilization.

Control of the feed oil pump.

Separate display for the truck data.

ADDITION OF FEED OILS

There are three variants available for adding feed oils via the progressing cavity pump:

  • External suction of external containers
  • The funnel for loose feed oils
  • Built-up additional tanks up to 1200 ltr. (depending on machine type)

DRIVE CONCEPT

Gentle on the truck power take-off.

When the PTO transmission is engaged, the system is almost load-free.

The shredding units are switched on automatically as required and the mixer drive is switched on automatically after a few seconds.

This not only protects the truck drive, it also avoids unnecessary fuel consumption.

Driving operation with the power take-off switched on is possible.

THE DISPENSING SYSTEM

In vehicles with air suspension, the measured values of the air bellows are determined via sensors, converted to the total mass, shown as axle load and mixed content in the Monitron, which can be tared at any time.

This enables the adequately precise dosing of partial quantities of the total mixture into different storage locations.

THE PRACTICAL

Practical switching functions in the driver’s cab for switching on the drive.

Hydraulic lifting / lowering / swiveling of the discharge auger.

Optionally also switching on the emptying auger.

Switching the work lights on and off (6x work lights as standard).

THE COMPONENT HOPPER

With a loading height of only 890 mm (depending on the chassis) made of stainless steel.

User-friendly accessible from three sides.

The inclined feed screw with clockwise / anti-clockwise rotation function enables easier cleaning of the screw windings and residual amounts emptying through suction and cleaning flap.

Taking feed samples via the mixer control slide is possible at any time.

Options:

  • Hydraulic bag lifting device
  • An integrated dust extraction

& nbsp;

THOUGHT OF YOU

All units are freely accessible. Lubrication points are brought together to allow easy lubrication.

Fuel consumption = a practical value under 2.5 liters. per ton of compound feed.

FN3007

Always the right solution.
Technically as well as economically!

& nbsp;

  • Short wheelbase
  • Powerful
  • Economical

Technical data FN3007

  • Antrieb: Motorabhängig / Nebenantrieb NMV
  • Nenndrehzahl: 1330 1/min
  • Mischerinhalt: max. 8800 – 11500 Liter
  • Mischerinhalt: max. 5000 – 6500 kg
  • Gesamthöhe: 3500 – 4000 mm
  • Breite: 2550 mm

& nbsp;

  • Truck: 2 axles
  • Wheelbase: 4200 mm
  • Screw discharge: up to 1000 kg / min
  • Pneumatic discharge: up to 800 kg / min
  • Hammer mill: up to 36000 kg / h
  • Grain crusher HQ300: up to 18000 kg / h
  • Total throughput in a continuous process: 40,000 kg / h

Do you have any questions about the FN3007
or our other grinding and mixing systems?

Contact us

4 + 14 =

S.M.H. Gmelin + Co.GmbH | Lembergstraße 19 | 72766 Reutlingen

+49 (0) 7121-479790

info@smh-gmelin.com